Process and Refining Operations Course Bundle
-
Open-Close
100 Industrial Math and Science (10)
170-01 Introduction to Industrial Math
170-02 Industrial Math: Measurements and Calculations
170-03 Industrial Math: Fractions, Percentages, and Ratios
171-01 Atomic Structure and Chemical Bonding
171-02 Introduction to the Periodic Table of Elements
171-03 Chemical Formulas, Reactions, and Solubility
171-04 Introduction to Hydrocarbon Chemistry
171-05 Chemical Equations
171-10 Introduction to Physics: Force and Motion
171-11 Introduction to Physics: Energy, Work, and Power -
Open-Close
200 Mechanical Maintenance (55)
201-01 Working Principles of Simple Machines
203-01 Introduction to Bearings
205-01 Introduction to Gear Drives
207-01 Lubrication Selection and Sampling in Rotating Machinery
207-02 Lubrication Failures and Management in Rotating Machinery
207-03 Lubrication Analysis in Rotating Machinery
208-01 Pipe Connections and Symbols
208-03 Piping Construction and Sizing
208-04 Piping Expansion, Support and Insulation
208-05 Piping Auxiliaries
209-01 Couplings
209-03 Pre-Alignment Procedures
209-04 Rough Alignment
209-05 Mathematical Rim-and-Face Alignment
209-06 Graphical Rim-and-Face Alignment
209-07 Reverse Dial Alignment
209-09 Laser Alignment
213-01 Lubrication Basics
213-04 Lubrication Filtration and Purification
215-01 Introduction to Valves and Their Components
215-02 Valve Actuators
215-03 Gate Valves
215-04 Globe Valves
215-05 Butterfly Valves
215-06 Ball Valves
215-07 Check Valves
215-08 Needle Valves
215-09 Plug Valves
215-10 Diaphragm Valves
215-11 Pinch Valves
215-12 Safety and Relief Valves
219-01 Introduction to Centrifugal Pumps
219-02 Centrifugal Pump Design
219-03 Centrifugal Pump Fundamentals
219-04 Centrifugal Pump Operation
223-01 Heat Exchanger Theory
223-02 Open Heat Exchanger Design and Operation
223-03 Closed Heat Exchangers
225-01 Compressed Air Systems
225-02 Compressed Air System Components
225-03 Positive Displacement Compressors
225-04 Dynamic Compressors
229-01 Bolted Joints
229-02 O-Rings
229-03 Making Gaskets
229-04 Fasteners
229-05 Packing Material Use and Installation
229-06 Mechanical Seals Use and Installation
231-01 Introduction to Positive Displacement Pumps
231-02 Reciprocating Positive Displacement Pumps
231-03 Rotary Positive Displacement Pumps
271-01 Vibration Introduction -
Open-Close
400 Electrical Maintenance (26)
401-01 Electron Theory
401-02 Magnetism and Electromagnetism Explained
401-03 Ohm’s and Kirchhoff’s Laws Relating to DC Circuits
401-04 Evaluating Series and Parallel DC Circuit Performance
401-05 Determine Circuit Outputs from Specified Inputs
402-01 Introduction to Alternating Current
402-02 Ohm’s and Kirchhoff’s Laws Involving AC Circuits
402-03 Inductance in AC Circuits
402-04 Capacitance in AC Circuits
402-05 Impedance in AC Circuits
402-06 AC Power
402-07 Fundamentals of 3-Phase AC
409-01 AC Induction Motors
409-02 AC Generators
411-01 Introduction to Motor Controls
415-01 Transformer Basic Operation and Theory
416-01 Battery Basics
417-01 Switchgear
417-02 Low Voltage Breakers
417-03 Medium and High Voltage Switchgear
417-04 General Switchgear Maintenance
417-05 Switchgear Specific Maintenance Procedures
417-06 Circuit Breaker Time Travel
418-01 Electrical Faults and Current Ratings
418-05 Grounding and Bonding
427-01 Electrical Freeze Protection Components and Application -
Open-Close
500 Power Generating Systems and Operations (46)
501-01 Energy Conversion
501-02 Steam Turbine Basics
501-03 Combustion System Component Overview
501-04 Boiler Water and Steam Cycle Overview
501-05 Generator Overview
505-01 Steam Turbine Design
511-01 Combustion Turbine Fundamentals
531-01 Combustion Theory
531-02 Basic Boiler Design
531-03 Boiler Valves and Fittings
531-04 Boiler Fuel and Air Systems
531-05 Boiler Water and Steam Cycle
531-06 Boiler Heat Recovery Systems
531-07 Boiler Environmental Controls
531-08 Boiler Operator Roles and Responsibilities
533-01 Fuel Combustion and Controls
533-02 Boiler Burner Controls and Management
535-01 Flue Gas Desulfurization System
535-02 Flue Gas Desulfurization System (FGDS) Open Spray Design, Part 1
535-03 Flue Gas Desulfurization System (FGDS) Open Spray Design, Part 2
535-04 Dry Scrubber Operation
535-05 Selective Catalytic Reduction (SCR)
551-01 Introduction to the Circulating Water System
559-01 Molecular Chemistry of Water
559-02 Elements and the Periodic Table of Elements
559-03 Chemical Compounds
559-04 Corrosion Causes and Effects
559-05 Corrosion Control in Steam Production
559-06 Steam Chemistry Control and Guidelines
559-07 Water Treatment Systems
563-02 Water and Steam Terms and Principles
563-03 Heat Transfer Principles
563-04 Laws and Principles of Thermodynamics
563-05 Performance Parameters
563-06 Balancing Efficiency, Availability, Capability and Flexibility
563-07 Instrumentation and Controls
563-08 Boiler Efficiency
563-09 Boiler Reliability
563-14 Pump Efficiency and Reliability
563-15 Environmentally Sensitive Operations
565-01 Distributed Control System Fundamentals
565-02 DCS Components
565-03 Using DCS Diagrams
567-01 Understanding the Basic Properties of Water and Steam
567-02 Saturated Steam Tables
567-03 Superheated Steam Tables -
Open-Close
600 Instrumentation and Control (20)
603-01 Instrumentation and Control Overview
603-02 Principles of Temperature
603-03 Principles of Pressure
603-04 Principles of Level
603-05 Principles of Flow
603-06 Temperature Instruments
603-07 Pressure Measuring Devices
603-08 Level Measuring Devices
603-09 Flow Measuring Devices
603-15 Weight Measuring Devices
607-01 Analytical Instruments
607-02 Introduction to Analytical Testing
611-01 P&ID Basics
611-02 Reading a P&ID
611-03 Electrical Drawings
611-04 Logic Diagrams
611-05 Industrial Print Reading Overview
613-01 Introduction to Automated Control
613-02 Pneumatic and Electronic Control System
621-01 Introduction to Programmable Logic Controller s (PLC) -
Open-Close
700 Process Systems and Operations (19)
701-01 Introduction to Petroleum Refining
701-02 Basic Petroleum Chemistry
701-03 OSHA’s Process Safety Management Standard
701-04 History of Refining
707-01 Features and Operation of Process Heaters
709-01 Features and Uses of Process Tanks
711-01 Introduction to Distillation
711-02 Operation of a Distillation Column
713-01 Introduction to Process Separators
715-01 Introduction to Process Reactors
717-01 Introduction to Methane Reforming and Synthesis
719-01 Safety Alarm Systems and Instrumentation
719-02 Overpressure Safety systems
721-01 Process Utilities System, Part 1
721-02 Process Utilities System, Part 2
723-01 Process Product Movement and Shipment
723-02 Tanks and Vessels used for Storage
725-01 Sampling Principles and Methods
725-02 Testing Principles and Procedures